| Fatigue Life | After 100,000 Compression Cycles, The Rebound Attenuation Is ≤ 3% |
|---|---|
| Medium Resistance | Resistant To Immersion In Engine Oil And Coolant For 168 Hours |
| Temperature Range | Operating In The Full Temperature Range From -40℃ To 125℃ |
| Friction Material | German Raybestos Composite Fiber Material |
| Shock-absorbing Spring | Oil-quenched And Tempered Spring Steel Wire |
| High Temperature Stability | 250 ℃ High Temperature Compression Permanent Deformation Rate ≤ 1.5% |
|---|---|
| Temperature Range | -40 ℃ To 125 ℃ Full Temperature Range Operation |
| Carrying Capacity | Rated Transmission Torque 1200N ・ M |
| Identification And Traceability | Pressure Plate Hub Laser Etching Model |
| Main Material | HT250 Gray Cast Iron Material |
| Surface Protection | Electrophoretic Primer + Polyester Topcoat Double-layer Anti-corrosion Coating |
|---|---|
| Temperature Range | Operating In The Full Temperature Range From -40℃ To 125℃ |
| Compatibility Design | Can Replace The Same Specification WABCO 9700514350 |
| Main Material | High-strength Aluminum Alloy Cylinder Block |
| Long-distance Passenger Transport | 300,000 Kilometers Maintenance-free Design |
| Vane-type Hydraulic Pump | Efficient And Stable, With Low Noise And Long Service Life |
|---|---|
| Electric Drive | Powered By The Vehicle's High-voltage Battery |
| Motor Interface | High-voltage Waterproof Connector |
| Motor Speed | 3000-6000rpm |
| Original Factory Part Number | 2121-00041 |
| Overload Protection | Automatically Relieve Pressure When The Air Pressure Exceeds 1MPa |
|---|---|
| Main Airbag Module | Provide Seat Suspension And Shock Absorption Function |
| Structural Strength | The Overall Design Load-bearing Capacity Is ≥ 200kg |
| Manual Adjustment | Control Knobs Are Set On The Side Of The Seat. |
| Lumbar Support Airbag | Made Of Medical-grade TPU Material |
| Convenience Of Modification | Comes With A Complete Set Of Accessories Including A Lock Body, Pull Rod, Sealing Ring, And Mounting Screws |
|---|---|
| Automatic Anti-lock Function | When The Door Is Closed, The Deadbolt Automatically Snaps Into The Strike Plate. |
| Impact Resistance Performance | The Compressive Strength Of The Lock Body Is ≥ 500MPa |
| Lever Linkage | Standard Configuration: 300mm Adjustable Pull Rod |
| Main Material | The Lock Body Is Formed By Zinc Alloy Die Casting. |
| Panel Material | High-strength PC+ABS Engineering Plastic |
|---|---|
| Service Life | Design Life ≥ 10 Years / 500,000 Kilometers |
| Automatic Mode | Built-in PID Intelligent Algorithm |
| Air Volume Control | 5-speed Wind Settings |
| Display System | LCD Display Screen |
| Type | Air Conditioning Compressor Pulley / Cooling Fan Drive Pulley |
|---|---|
| Bearing Specifications | Built-in 6203-6306 Series Deep Groove Ball Bearings |
| Original Factory Model | 29XG5-35501/HFF6123K40 And Other Series |
| Material | High-strength Cast Iron |
| Operating Temperature | -40℃~120℃ |
| Core Structure | Pneumatic Control Valve + Hydraulic Master Cylinder + Power Piston + Return Spring |
|---|---|
| Rated Thrust | Maximum Output Thrust ≥ 4500N |
| Execution Standard | Compliant With QC/T362-2011 |
| Work Pressure | Air Pressure 0.6-0.8MPa |
| Sealing Grade | IP54 Protection Standard |
| Genuine OE Part Number | 4891252, Authentic -engineered Water Pump, Traceable Via Official Verification System |
|---|---|
| High-Performance Cooling | Max Flow Rate 120L/min, Optimized Impeller Design Enhances Heat Dissipation Efficiency By 30% |
| Anti-Cavitation Technology | Special Impeller Blade Design Prevents Air Bubble Formation, Ensuring Stable Water Flow |
| Maintenance-Free | Sealed Bearing & Pre-filled Lubricant, No Periodic Maintenance Needed Under Normal Use |
| Operating Pressure | Rated Working Pressure 150kPa, Peak Pressure Up To 200kPa, Stable Under Extreme Loads |