| Range | LED Model ≥200 Meters / Xenon Model ≥250 Meters |
|---|---|
| Quality Commitment | Inspection One By One, With A Pass Rate Of 100% |
| Packaging | Carton, Wooden Box, Custom Packaging |
| Shell | Aviation Aluminum Heat Dissipation |
| Illuminance Value | 20 Meters Away, ≥300 Lux. |
| Quality Commitment | Inspection One By One, With A Pass Rate Of 100% (supporting Attached Inspection Reports) |
|---|---|
| Packaging | Carton, Wooden Box, Custom Packaging |
| Low-temperature Starting Performance | -20℃ Cold Friction Coefficient ≥ 0.3 |
| Wear Rate | ≤0.3mm / Ten Thousand Times |
| Material Type | Ceramic Composite Sheet |
| Quality Commitment | Inspection One By One, With A Pass Rate Of 100% (supporting Attached Inspection Reports) |
|---|---|
| Accessory Type | Fast Transmission Parts |
| Applicable Scenario | Bus Truck |
| State | Brand New |
| International Certification | CE/ISO 9001/DOT |
| Packaging | Carton, Wooden Box, Custom Packaging |
|---|---|
| International Certification | GB/T 35180-2017 ,ISO 9001,TS 16949 |
| Interface Standard | Adapt To A Hole Diameter Of Φ85mm. |
| Metal Insert | 40Cr Quenched And Tempered Steel |
| Size | D=85,d=19,S=130*t=30 |
| Packaging | Carton, Wooden Box, Custom Packaging |
|---|---|
| Fatigue Life | 10⁶ Times Of Loop Without Breakage. |
| Applicable Scenario | Bus Dongfeng Dana Axle |
| International Certification | GB/T 17485+ECE R117 |
| Size | φ20.5mm L=128mm |
| Packaging | Carton, Wooden Box, Custom Packaging |
|---|---|
| Key Life | 100,000 Presses Of Silicone Keys |
| Shell Material | ABS Engineering Plastic |
| Accessory Type | Door Remote Control |
| Control Channel | Single-door Control |
| Quality Commitment | Inspection One By One, With A Pass Rate Of 100% |
|---|---|
| Packaging | Carton, Wooden Box, Custom Packaging |
| B10 Life | Have A B10 Life Of 5000 Hours. |
| Waterproof Level | Reach IP67 Waterproof Rating. |
| Speed Range | Between 2000 - 4000 Rpm. |
| High Load Capacity | Maximum Bearing Torque Is 200 N·m And Is Suitable For Large-displacement Engines. |
|---|---|
| High Temperature Resistant Seal | Fluororubber Oil Seal, Capable Of Withstanding High-temperature Oil At 180℃. |
| Millisecond-level Response | Adapt To Engine Speed Fluctuations And Maintain Transmission Stability. |
| Anti-corrosion Coating | Electrophoretic Treatment. Salt Spray Test For 1000 Hours Without Rust. |
| Dynamic Tension Compensation | Real-time Adjustment Of Belt/chain Tension With An Error Of ±0.5 N·m. |
| Millisecond-level Adaptive Response | Support Dynamic Adjustment Under Complex Working Conditions Such As Cold Start Of The Engine And Rapid Acceleration. |
|---|---|
| Overspeed Protection | When The Rotational Speed Is Greater Than 6000 Rpm, Locking Is Triggered To Prevent The Tensioner Pulley From Flying Off. |
| Timing Synchronization Guarantee | Accumulated Error Is Less Than ±0.5° Crankshaft Angle To Avoid The Risk Of Knocking Caused By Valve Timing Deviation. |
| Material And Craftsmanship | Adopt QT700-2 Nodular Cast Iron. The Tensile Strength Is ≥700 MPa. The Fatigue Life Is Over 1 Million Times. |
| High-temperature Fatigue-resistant Coating | The Surface Is Sprayed With Molybdenum Disulfide (MoS₂) Dry Film, And The Friction Coefficient Is ≤0.05. |
| High-strength And Wear-resistant | Adapt To The Frequent Shifting Needs Of Heavy Vehicles. |
|---|---|
| Anti-fatigue Design | Cycle Life Exceeds 500,000 Times Without Deformation. |
| Shock Absorption | Rubber Damping Block Reduces Shift Shock. |
| Quick Response | Complete Gear Shifting Within 0.2 Seconds. |
| Low Temperature Startup Optimization | Work Normally In An Environment Of -40℃. |