| Low Battery Reminder | When The Voltage Is Less Than 2.6V, The Key Backlight Flashes. |
|---|---|
| Models Applicable To | Jinlong, Yutong, Zhongtong Buses |
| Antenna Type | Built-in FPC Flexible Antenna |
| Single Door Independent Control | Pneumatic Door Adaptation |
| General Interface | 5PIN Waterproof Terminal |
| Applicable To | Mainstream Bus Brands Such As Yutong, King Long, Zhongtong, Higer, And Golden Dragon |
|---|---|
| Fatigue-resistant | No Deformation After 100,000 Cycles Of Testing |
| Regulating Device | Used To Adjust The Length Of The Pull Rod |
| Pneumatic Door Pump Pull Rod | For Pneumatic Outward-swinging Doors |
| Pneumatic System | Working Pressure 0.4-0.8MPa |
| Models To Be Adapted | Shaanxi Auto Delong / Foton Auman / Yutong King Long Bus |
|---|---|
| Material Composition | High-strength Aluminum Alloy Shell |
| Tensile Force Characteristics | Rated Tension Force 800 - 1200N |
| Fatigue Life | 1 Million Times Of Loop Loading |
| Working Principle | Planar Spring Torsion Structure |
| Multi-vehicle Model Adaptation | Compatible With Buses Such As Yutong, King Long, Higer, Etc. |
|---|---|
| Installation Adaptation | The Thickness Of The Car Door Is 40 - 60mm |
| Switch Life | ≥300,000 Times |
| Main Body Material | Stainless Steel |
| Operating Temperature Range | -35℃~+70℃ |
| Installation Accuracy | The Tolerance Of The Distance Between The Lock Body Installation Holes Is ±0.5mm |
|---|---|
| Compatible With Multiple Vehicle Models | Suitable For Buses Such As Yutong / King Long |
| Main Body | Zinc Alloy Die - Cast Housing |
| Temperature Resistance | - 40℃~120℃ |
| Anti-vibration Level | 20-2000Hz |
| Adaptation Specifications | Compatible With Buses Such As King Long, Yutong, And Higer |
|---|---|
| Fatigue Life | The Mechanical Lifespan Of The Key Is ≥ 100,000 Presses |
| Anti-interference Design | DSSS+FHSS Hybrid Spread Spectrum Technology |
| Wide Temperature Operation | Stable Operation From -20℃ To 60℃ |
| Operation Response | Key Trigger Response Time ≤ 50ms |
| High Temperature Stability | 250 ℃ High Temperature Compression Permanent Deformation Rate ≤ 1.5% |
|---|---|
| Temperature Range | -40 ℃ To 125 ℃ Full Temperature Range Operation |
| Carrying Capacity | Rated Transmission Torque 1200N ・ M |
| Identification And Traceability | Pressure Plate Hub Laser Etching Model |
| Main Material | HT250 Gray Cast Iron Material |
| Motor Configuration | 24V Permanent Magnet Synchronous Motor |
|---|---|
| Air Volume And Air Pressure | Rated Air Volume 2500m³/h |
| Noise Control | No-load Noise ≤ 68dB (A) |
| Protection Level | IP55 Dustproof And Waterproof |
| Impeller Material | High-strength Aluminum Alloy Die-cast Impeller |
| Environmental Resistance Performance | 720 Hours Of Neutral Salt Spray Test With No Corrosion |
|---|---|
| Fatigue Life | After 1,000,000 Cycles Of Load Testing |
| Buffering Performance | Preset 25% Compression Amount |
| Installation Method | Fixed By The Central Bolt |
| Load Capacity | Static Limit Load ≥ 50kN |
| Work In The Full Temperature Range | Stable Operation In An Environment Ranging From -40℃ To 85℃ |
|---|---|
| Pressure Drop Control | Initial Pressure Drop At Rated Air Volume ≤ 2kPa |
| Quality System | Produced By IATF 16949 Certified Factories |
| Precise Matching | Original Factory Number 1109-08269 |
| Dust Holding Capacity | Static Dust Holding Capacity ≥ 300g |