| Protection Level | IP65 Level Dustproof And Water Spray Proof |
|---|---|
| Typical Working Conditions | City Buses Start And Stop Frequently. |
| Load Capacity | Rated Thrust ≥ 1200N |
| Installation Method | Flange Installation |
| Lifespan | ≥20000 Hours |
| Temperature Adaptation | -40℃ Low-temperature Startup Without Jamming |
|---|---|
| Salt Spray Test | 96 Hours Without Red Rust |
| Dust Cover Fixing | 65Mn Spring Snap Ring |
| Extended Maintenance Cycle Without Lubrication | 100,000 Kilometers |
| Dimensional Accuracy | Ra≤0.8μm |
| Working Condition Adaptation | Designed Specifically For The Frequent Starts And Stops Of Urban Public Transport |
|---|---|
| High-temperature Durability | 130℃ Constant Temperature Durability Test For 400h With No Performance Drift |
| Wide Temperature Operation | Stable Operation Over The Entire Temperature Range From -40℃ To 125℃ |
| Response Speed | The Response Time To Sudden Changes In Rotational Speed Is ≤ 5ms |
| High Temperature Durability | 130℃ Constant Temperature Durability Test For 400h |
| Cold Adaptation | The Increase In Separation Force During Cold Start At -30℃ Is ≤ 15% |
|---|---|
| Environmental Adaptation | -40℃ To 120℃ Temperature Cycling 200 Times Without Cracks |
| Heart Structure | Flatness Of The Pressure Plate Working Surface ≤ 0.05mm/m |
| Thermal Stability | The Friction Coefficient Retention Rate At 350℃ Is ≥ 85% |
| Spring Layout | 36 Springs Are Symmetrically Distributed In 6 Groups |
| Environmental Adaptation | Operating Temperature -40℃ To +125℃ |
|---|---|
| Lightweight Design | Aluminum Alloy Shell Accounts For 70% |
| Efficiency Characteristics | Power Generation Efficiency ≥ 88% |
| Electromagnetic Compatibility | Radiated Disturbance ≤ 30dBμV/m |
| Starting Performance | -30℃ Cold Cranking Current ≤ 180A |
| Easy To Maintain | The Design Life Of The Brush Assembly Is ≥ 150,000 Kilometers |
|---|---|
| Protection Level | The Entire Machine Has IP54 Dust And Water Resistance Rating |
| Material Technology | The Shell Is Made Of ADC12 Aluminum Alloy By Die Casting. |
| Speed Characteristic | Idle Condition (800±50r/min) Output ≥ 60A |
| Efficiency Performance | Efficiency ≥ 85% At 75% Load |
| Temperature Adaptation | Operates In The Full Temperature Range From -40℃ To 125℃ |
|---|---|
| Environmental Testing | -40℃ To 125℃ High And Low Temperature Cycle Test |
| Material Composition | The Main Body Is Made Of A356 Aluminum Alloy |
| Load Capacity | Static Torque Bearing Capacity ≥ 850N・m |
| Vibration-resistant Design | Built-in Rubber Shock-absorbing Bracket |
| Intermittent Frequency Adjustable | The Intermittent Wiper Mode Supports Stepless Adjustment From 3 To 15 Times Per Minute. |
|---|---|
| Temperature Range Adaptation | Stable Operation Over The Entire Temperature Range From -40℃ To 85℃ |
| Service Life | The Overall Mechanical Service Life Is ≥ 100,000 Operating Cycles |
| Insulation Protection | The Insulation Resistance Of The Ontology Is ≥ 100MΩ |
| Vehicle Model Coverage | Designed Specifically For The Higer Series |
| Work In The Full Temperature Range | Stable Operation In An Environment Ranging From -40℃ To 85℃ |
|---|---|
| Pressure Drop Control | Initial Pressure Drop At Rated Air Volume ≤ 2kPa |
| Quality System | Produced By IATF 16949 Certified Factories |
| Precise Matching | Original Factory Number 1109-08269 |
| Dust Holding Capacity | Static Dust Holding Capacity ≥ 300g |
| High Temperature Stability | 250 ℃ High Temperature Compression Permanent Deformation Rate ≤ 1.5% |
|---|---|
| Temperature Range | -40 ℃ To 125 ℃ Full Temperature Range Operation |
| Carrying Capacity | Rated Transmission Torque 1200N ・ M |
| Identification And Traceability | Pressure Plate Hub Laser Etching Model |
| Main Material | HT250 Gray Cast Iron Material |