| Compatible Vehicle Models | Yutong Models Such As ZK6120H/6118Y2/6805DX |
|---|---|
| Storage Conditions | Dry And Light - Avoiding Environment |
| Fatigue Life | 1 Million Times Of Swing Angle Cycles |
| Structural Design | Double-ball Seat All-metal Joint |
| Disassembly Tools | 27mm Plum Blossom Wrench |
| Pressure Characteristics | Turn On The Pressure Deviation ≤ ±0.3 Bar |
|---|---|
| Certification Standards | QC/T 29105+ IATF 16949:2016 |
| Sealing System | Double - Lip Sealing Structure |
| Structural Design | Spring-loaded Plunger Valve |
| Lubrication System | Lithium-based Grease Filling |
| Length | L=250mm,L=275mm |
|---|---|
| Shaft Diameter | Φ35mm,Φ40mm |
| Damping Coefficient | 10~12N・s/mm |
| Base Material | 40Cr Alloy Steel |
| Critical Speed | ≥8000r/min |
| Typical Dimensions | Outer Diameter Φ88mm × Inner Diameter Φ50mm × Height 67mm |
|---|---|
| Full-wrapped Structure | The Two Ends Of The Metal Shell Are Bent Inwards By 3mm. |
| Mainstream Adaptation | DongfengDena 435/460/485 Single-stage Reducing Axle |
| Metal Framework | Q345B Low Alloy High Strength Steel |
| Wear-resistant Layer | Polyoxymethylene (POM) Ball Bowl |
| Fatigue Life | ≥200ten Thousand Times |
|---|---|
| Salt Spray Test | No Corrosion Within 480h |
| Material | Specialty Rubber |
| Dynamic Stiffness | 300~500N/mm |
| Hardness | 70±5 Shore A |
| High-resolution Detection | The Minimum Identifiable Oil Level Change Is 3mm |
|---|---|
| Compatible With Multiple Vehicle Models | Suitable For Higer KLQ6129, KLQ6896, Etc. |
| Pressure Resistance And Impact Resistance | Pressure Bearing Range - 0.1MPa~32MPa |
| Low Fuel Warning | The Trigger Threshold Is Configurable |
| Fast Response Characteristics | Signal Update Frequency ≤ 100ms |
| Low Friction Design | Copper-based Self-lubricating Bushings Are Used, And The Friction Coefficient Is ≤ 0.08. |
|---|---|
| Security Authentication | The Support Assembly Passes The 1.5 Times Static Load Test |
| High-precision Cooperation | Tolerance Of Rocker Arm Shaft Hole ±0.01mm |
| Wide Temperature Adaptability | Operating Temperature Range - 40℃~120℃ |
| Install | Dedicated Car Customization Interface |
| Low - Temperature Starting Performance | The Response Time Is ≤80ms In An Environment Of - 30℃ |
|---|---|
| Flow Characteristics | Fast Charging / Slow Charging Dual Mode |
| Service Life | ≥ 1 Million Opening And Closing Cycles |
| Misoperation Protection | Overload Protection |
| Valve Core Material | Stainless Steel 304 |
| Optional Upgrade Package | Containing Throttle Valve And Solenoid Valve |
|---|---|
| Certification Standards | Pass CCC Certification And ISO 16949 |
| Compatible Gate Pump | MB50-180, MB-N, MB-100, Etc. |
| Lifespan | ≥100,000 Loop Cycles |
| Applicable Vehicle Models | 10 - 18 Meter Buses |
| Service Life | ≥800,000 Opening And Closing Cycles |
|---|---|
| Configuration | Front Door Opens. Rear Door Opens. |
| Anti-pinch Protection Function | Air Pressure Feedback Sensor |
| Drive Form | Single-cylinder Linkage Type |
| Speed Regulation Function | Two-way Throttle Valve |