| Range | LED Model ≥200 Meters / Xenon Model ≥250 Meters |
|---|---|
| Quality Commitment | Inspection One By One, With A Pass Rate Of 100% |
| Packaging | Carton, Wooden Box, Custom Packaging |
| Shell | Aviation Aluminum Heat Dissipation |
| Illuminance Value | 20 Meters Away, ≥300 Lux. |
| Quality Commitment | Inspection One By One, With A Pass Rate Of 100% |
|---|---|
| Packaging | Carton, Wooden Box, Custom Packaging |
| Accessory Type | Transmission Accessories |
| Model | QC4000-02,2214-00146 |
| Applicable Scenario | Bus Transmission Shaft |
| Packaging | Carton, Wooden Box, Custom Packaging |
|---|---|
| Emergency Unlocking Type | Cockpit Pull Wire + Mechanical Key |
| Protection Level | IP67 (lock Body)/IP54 (keyhole) |
| Accessory Type | Engine Hood Mechanical Lock |
| International Certification | GB 15743-2022 |
| Long Life And Durability | Adopting High-quality Lamp Beads, The Service Life Can Reach More Than 50,000 Hours. |
|---|---|
| High Brightness Lighting | Ensure Sufficient Lighting In The Carriage To Meet The Needs Of Reading And Passage. |
| Multicolor Ambient Light | Support Single-color Or Gradient Mode To Create A Comfortable Atmosphere. |
| Soft And Not Dazzling | Adopt Warm Light Or Soft Light Design To Protect Passengers' Eyesight. |
| Low Power Consumption Design | Reduce Vehicle Energy Consumption And Improve Cruising Range. |
| Suspension Type | Air Spring,Air Bellow |
|---|---|
| Adapt | Mercedes-Benz Bus |
| Structural Design | Maintenance-free |
| Advantages | Height Adjustable |
| Product Material | Natural Rubber |
| Intelligent Sleep | The Vehicle Automatically Enters Sleep Mode After Being Stationary For 15 Minutes. |
|---|---|
| Communication Specifications | Operating In The 433.92±0.05MHz SRRC Approved Frequency Band |
| Alarm Response | The Response Time For Rapid Air Leakage Detection Is ≤ 5 Seconds |
| Material Technology | The Shell Is Made Of PA66 + 30% Glass Fiber Reinforced Material |
| Protection Level | Sensor Body IP6K9K Dustproof And Waterproof |
| High Temperature Stability | 250 ℃ High Temperature Compression Permanent Deformation Rate ≤ 1.5% |
|---|---|
| Temperature Range | -40 ℃ To 125 ℃ Full Temperature Range Operation |
| Carrying Capacity | Rated Transmission Torque 1200N ・ M |
| Identification And Traceability | Pressure Plate Hub Laser Etching Model |
| Main Material | HT250 Gray Cast Iron Material |
| Maintenance Cycle | It Is Recommended To Check The Lubrication Status Every 20,000 Kilometers. |
|---|---|
| Installation Method | The Bearing Seat Is Connected To The Release Fork Via A Return Spring. |
| Main Material | The Outer Ring Is Made Of SUJ2 High-carbon Chromium Bearing Steel |
| Transmission Adaptation | Specially For Qijiang S6-90, S6-100, QJ805, QJ1506, Etc. |
| Interface Adaptation | Precisely Fits With The Groove Of The Clutch Fork |
| Accessory Type | Hydraulic Clutch Master Cylinder With Central Valve Structure |
|---|---|
| Core Structure | Central Valve + Built-in Set Screw + Guide Sleeve Piston |
| Material Composition | High-strength Cast Aluminum Cylinder Block |
| Implementation Standard | Compliant With QC/T593-2011 |
| Interface Specification | Oil Outlet M14×1.5 Thread |
| Accessory Type | Bidirectional Acting Hydraulic Steering Damper |
|---|---|
| Condition Adaptation | -40℃~+80℃ Wide Temperature Operation |
| Compatible Scenarios | Suitable For 12-14 Meter Three-axle Buses |
| Stability Performance | Suppressing Steering Wheel Shimmy |
| Cylinder Bore Specification | φ45mm High-pressure Oil Cylinder |